Linksys Extender Setup

Linksys Extenders increases the strength and coverage of your home Wifi. It detects the signal from your router before sending it to your devices for instance computer, laptop or mobile to spice up the coverage of your network. Hence, it provides wifi connectivity in hard-to-reach areas and ejects al the dead zones. By following the below-given guide, you'll easily install your Linksys Extender.

There are two ways to configure your Linksys Extender- Manual Method and WPS Method.

Method 1: Linksys Extender Configuration Via Manual Method:

Plug the Range Extender to the facility Source:

Attach the additional antennas of your extender perfectly. The antennas must be in an upright position for getting the simplest internet speed.
Now, find a midway where you'll place your extender. It should be in between your router and therefore the area without Wifi.
After that, take an influence cable. Then, you would like to insert the one end of the facility cable to the port of the extender and another end to the wall socket .

Check the Status of Your Extender:

You can monitor the status of your extender by checking its LED lights. the facility LED lights must be solid and properly lit.

Build a Connection Between the Extender and Your Device:

To perform Linksys Extender Setup through the web site , you've got to link the extender with the pc , laptop or mobile device.
If you would like to line a wireless connection, find the default name of your extender i.e. Linksys Extender Setup within the Wifi list and click on Connect.
But for a wired setup, you would like to accumulate an coaxial cable . Then, plug the one end of the cable to the extender and another end o the pc .

Setup your Linksys Extender Through the Website:

To access the Linksys Extender Setup page, you'll open any browser like Chrome, Safari, etc. on your device.
After that, type extender.linksys.com within the address bar and hit Enter on your keyboard. instead of , you'll use the default IP address of the range extender i.e 192.168.1.1.
Now, the Linksys login page will inherit view. Here, you're alleged to type “admin” within the password field and press Login.
This will launch the Linksys Extender Setup page. Click on the top User License Agreement link then read the entire document carefully. To proceed further and for Linksys Extender Setup, tick the checkbox “I accept the top User License Agreement”.
Also, for automatic software updates, select the checkbox given there.
In the next window, the user are going to be given an choice to select between “As a wireless Range Extender” or “As a wired Range Extender”. So, choose one among the choices consistent with your preference.
This will launch the Wireless Network window on your display screen . Select your network name(SSID) from the available list of Wifi that's in range.
After that, you would like to supply the wireless password that you simply have set for your wifi. After entering the password, click Next.
With this, you'll see a window of Extender Configuration on which you've got to vary the default settings of your extender. So, provide a replacement extender name and password into their respective fields and click on Next.
As your extender comes with Spot Finder Technology, it'll assist you to seek out the precise and proper location for your extender. So place your extender within the right position as guided by this technology. But you'll also prefer to skip this step by clicking on the Connect Anyway button.
Now, it'll show you the Secure your range extender screen. Do the following:
The user will need to provide an admin password that has got to be strong enough to dam unauthorized access.
Also, confirm the password by typing it again into subsequent field.
Now, you'll tend an choice to provide a touch to your password for remembering your password.
After that, press subsequent button.
Finally, you'll see the Setup complete window on your screen which specifies that Your Linksys setup.

Method 2: Wifi Protected System Method

WPS Method is beneficial in establishing a robust connection between the extender and devices. Either, you'll use the WPS physical button given on the router or access the extender.linksys.com website.

* Using the WPS Button:

Plug the Extender to the facility outlet and assure that it's properly connected.
After that, press the WPS button on your extender. you'll find this button on the front-side of your extender.
Also, the LED lights of your extender should blink.
After checking the lights, you've got to press the WPS button on your router.
The WPS light will turn color to solid green when the connection between your router and extender gets established.

* By providing the WPS PIN or Router’s PIN.

Launch any browser and punctiliously type extender.linksys.com within the address bar.
This will open the Linksys Extender Setup page on your screen. Here you'll need to click on the Wireless tab which is provided to you at the highest of the page.
To proceed further, you're required to pick the “Wi-Fi Protected Setup” radio button.
After that, enter your WPS PIN or Router’s PIN into the given fields as per your preference.
Then, click on the Register button.
To make sure that the connection is established, check the LED light on your extender. If it's stable and properly lit, your extender is now connected to the router.

Search This Blog